How Do I Tie a Knot in Fishing Line

Fishing using feeder or matchFishing rod requires the angler to implement long-range and accurate casting tackle. For this, anglers very often use sliding equipment. It is this that makes it possible to control the casting distance by adjusting the position of the float. This is done with the help of various locking devices on the main tackle line. One of them is a locking slide assembly. About it, we'll talk, and also consider options for his right knitting.

Why you need a sliding float

A sliding float is used mainly forfishing from the bottom, as well as at a long distance from the fisherman. Its difference from the usual biting pointer lies in the fact that it is attached to the main line not "tightly", but with the possibility of free movement along it in a certain range established by the fisherman.

When casting such a float is inclose proximity to the cargo, which allows you to "throw" the tackle as far as possible. Once in the water, the cargo with the hook falls to the bottom, and the bite pointer slides along the line upwards until it stops the locking sliding assembly or other similar device. At the same time, under the action of two forces, one of which pushes the float to the surface and the other pulls to the bottom, it will solidify and rise vertically.

Such a float does not lose its sensitivity at all, but, on the contrary, reacts to any vibration of the rigging.

Stoppers for float

As a stopper, differentDevice, like rubber or silicone beads, worn on the main line. They are freely sold in fishing shops and markets, and are worth a penny.

But still the most popular and widespreadmeans for fixing the float remains a sliding knot, invented by savvy anglers. To tie it, knowing at least one of the ways, does not present any complexity. And you can do this even at the fishing site, having a piece of fishing line near your hand or even an ordinary sewing thread.

If there is no desire to knit a locking knot forsliding float yourself, you can buy it. Yes, there are even knots sold in fishing shops today. Usually they are tied to a special tube, and the fisherman just remains that to remove the knot, put it on the fishing line and tighten.

But we will not be like lazy and unskilled fishermen, but we will practice how to knit such knots on our own.

Of what to knit

As for the material, the usual line is here -not the best choice. First, the frictional force in this case will be minimal. This will cause the node to move easily and cease to be a stop. And secondly, the line is quite transparent, and we need the upper limit of the float position to be constantly visible.

Most often the sliding knit is knitted from a piecea backing cord for fly fishing, a braided line or an ordinary thick thread (preferably woolen). The latter option is preferable to all, since it does not require any costs, but works most effectively.

What else do you need to know when starting knitting a locking knot

If you plan to fish usinga fishing rod, a stop knot should be given maximum attention. The fact is that the rod for match fishing has a lot of access rings, which have rather narrow holes. Because of this, when casting very often there is a situation where the node simply sticks in them. This, in turn, leads to the fact that the tackle not only does not fall into the intended place, but also becomes entangled.

To avoid such trouble, the stopperThe assembly for the sliding float should not only correspond to the size of the rings, but also be tightened well. In addition, its ends in any case can not be cut completely. First, it significantly worsens the passage through the access rings of the rod, and secondly, they will still be needed to tighten the knot when it loosens.

The main methods of knitting stop knots

There are many different ways to knit fishing knots, including stoppers. All of them, of course, can not be studied, so we will consider the simplest and most popular of them:

• "Clinch" - the simplest and fastest in the manufacture of a locking assembly for a sliding float;
• "Improved" knot - it is knit with the use of a needle;
• "Kremkus" is an uncomplicated double knot;
• "Danken" - the most practical and reliable node

How to fasten a sliding knot of the "clinch" type

Knot "clinch" is the easiest in knitting. Because of this, anglers most often use it. "Clinch" - a single node, but this does not mean that it is unreliable or inefficient. He does his job well.

To make it, we need a woolen thread of bright color of the same cross-section as the line. The knitting algorithm for the knot is approximately as follows:

1. The length of the thread length of 25-30 cm is folded in half and applied to the main line from the bottom, pressing with your fingers.
2. One of the ends of the thread is thrown through the fishing line and the other end so that the main line is inside the formed loop.
3. While holding the loop with your fingers, make 5-7 turns with the first end around the line and the second end.
4. The first end is passed in a loop, we moisten the unit with water or saliva and tighten.
5. Cut off the rest of the thread, leaving 2 cm on both sides.

Locking knots for fishing line type "clinch" because of their "elegance" for the most part are used for match equipment.

"Improved" (modified) node

Another version of a simple node. His knitting does not cause any difficulties at all, the only thing that should be at hand is a needle (better gypsy).

To associate an "improved" sliding node forfloat, take the thread, needle and apply them to the line (in parallel). Then one of the ends is wrapped all this, making 5-6 turns. Then we put the same end into the eye of the needle and stretch it out a little. We take out the needle in the direction of its point and, after moistening the knot, slowly tighten and cut off its ends.

"Kremkus" type node

"Kremkus" is a double knot, because it knits into two threads. It is much thicker and denser than the "clinch", but the process of knitting is also quite simple:

1. We fold the thread in half and wrap it around the line.
2. Around the loop formed we make 3-4 turns with both ends.
3. We wet the knot, tighten it and cut off the ends, not forgetting to leave around the edges of 2 cm.

Similar nodes are more often used in feeder gear.

How to make a sliding knot "danken"

Knot "danken" is considered the most practical. Tightening it once when knitting, you will not do this again. It reliably keeps on a scaffold and is not dismissed. To bind a sliding knot for a danken float, you must perform the following steps:

1. We bend the thread in half in half, and apply the loop at the intersection of the ends to the fishing line.
2. We skip one of the ends under the fishing line, pass it through a loop, repeating this step 4-5 times so that the lower part of the loop is wound to the fishing line in 4-5 turns.
3. We moisten the knot with water and slowly tighten it, spreading the ends to the sides.
4. Crop the ends, leaving 2 cm.

   

How to prepare nodes for future use

If you are a lover of match or feeder fishing, you will not do without locking knots in any case.

In order not to suffer with their knitting every time you mount the tackle, you can stock up on them in advance.

To do this, take a plastic tube likeampoules from a ballpoint pen or insulation of an electric wire 5-8 cm long and we will tie the required number of knots on it. Now you will always have a whole set of stoppers on hand. To use them, it is enough to put the tube on the main line, pull the extreme knot on it, hold it on the desired section, tighten and trim the ends.

How Do I Tie a Knot in Fishing Line

Source: https://ellas-cookies.com/sport-i-fitnes/105356-skolzyaschiy-uzel-kak-zavyazat-skolzyaschiy-uzel-uzly-dlya-leski.html

Share :